Hi Tom,
USB power yes but I took the wrong output now that I have HighPower output it all works OK and my spare KFlop now runs latest firmware.
This 64-bit circus makes many heads spin around until we all find the path to prpoer working conditions.
After a long delay I am now getting back on track with my CombiMill, had to tear down the gearbox and get new parts mostly bearings and it all took so long time so I had time to do some paintwork also. Soon some update on my website.
Cheers from Sweden to all 'Kflopers'
Bengt

--- In DynoMotion@yahoogroups.com, Tom Kerekes <tk@...> wrote:
>
> Hi Bengt,
>  
> That doesn't sound like a problem with the install.
>  
> Are you running from USB power?  If so can you try an external +5V supply?  I've seen some cases when the USB +5V was very low and caused something like this.
>  
> Regards
> TK
>
> From: Bengt Sjoelund <cnc@...>
> To: DynoMotion@yahoogroups.com
> Sent: Friday, December 16, 2011 1:33 PM
> Subject: [DynoMotion] Re: W7 64bit OS
>
>
>  
> Sorry Tom,
> Still not OK, Install did take very very looooooooooong time to pass and now KFlop is 'Unknown device'.
> Something is very wrong with the install package, I have downloaded 2 times still same odd behaviour. I can open Kmotion but not USB Locations as the board is not activated in the system.
>
> So what next?
> Cheers
> Bengt
>
> --- In DynoMotion@yahoogroups.com, Tom Kerekes <tk@> wrote:
> >
> > Hi Bengt,
> >  
> > Apparently the Install Shield version we use expects all open processes to respond to some request in a standard fashion and if not it hangs.  It normally works on W7 64.  Please try closing all other Apps and unnecessary Processes to see if that helps.
> >  
> > Regards
> > TK
> >  
> >
> > From: Bengt Sjoelund <cnc@>
> > To: DynoMotion@yahoogroups.com
> > Sent: Friday, December 16, 2011 11:49 AM
> > Subject: [DynoMotion] W7 64bit OS
> >
> >
> >  
> > Hi Tom,
> > I tried to install latest version on my office box with W7 64bit but I cannot get install to start up, yes I have tried to run as admin but still no go.
> > Any advise?
> > Cheers
> > Bengt
> >
>

Ha!
good one Bengt
'Kflopers'
it's a fun sounding name
"Mach-er" always sounded so harsh

Carl

--- In DynoMotion@yahoogroups.com, "Bengt Sjoelund" <cnc@...> wrote:
>
> Hi Tom,
> USB power yes but I took the wrong output now that I have HighPower output it all works OK and my spare KFlop now runs latest firmware.
> This 64-bit circus makes many heads spin around until we all find the path to prpoer working conditions.
> After a long delay I am now getting back on track with my CombiMill, had to tear down the gearbox and get new parts mostly bearings and it all took so long time so I had time to do some paintwork also. Soon some update on my website.
> Cheers from Sweden to all 'Kflopers'
> Bengt
>
> --- In DynoMotion@yahoogroups.com, Tom Kerekes <tk@> wrote:
> >
> > Hi Bengt,
> >  
> > That doesn't sound like a problem with the install.
> >  
> > Are you running from USB power?  If so can you try an external +5V supply?  I've seen some cases when the USB +5V was very low and caused something like this.
> >  
> > Regards
> > TK
> >
> > From: Bengt Sjoelund <cnc@>
> > To: DynoMotion@yahoogroups.com
> > Sent: Friday, December 16, 2011 1:33 PM
> > Subject: [DynoMotion] Re: W7 64bit OS
> >
> >
> >  
> > Sorry Tom,
> > Still not OK, Install did take very very looooooooooong time to pass and now KFlop is 'Unknown device'.
> > Something is very wrong with the install package, I have downloaded 2 times still same odd behaviour. I can open Kmotion but not USB Locations as the board is not activated in the system.
> >
> > So what next?
> > Cheers
> > Bengt
> >
> > --- In DynoMotion@yahoogroups.com, Tom Kerekes <tk@> wrote:
> > >
> > > Hi Bengt,
> > >  
> > > Apparently the Install Shield version we use expects all open processes to respond to some request in a standard fashion and if not it hangs.  It normally works on W7 64.  Please try closing all other Apps and unnecessary Processes to see if that helps.
> > >  
> > > Regards
> > > TK
> > >  
> > >
> > > From: Bengt Sjoelund <cnc@>
> > > To: DynoMotion@yahoogroups.com
> > > Sent: Friday, December 16, 2011 11:49 AM
> > > Subject: [DynoMotion] W7 64bit OS
> > >
> > >
> > >  
> > > Hi Tom,
> > > I tried to install latest version on my office box with W7 64bit but I cannot get install to start up, yes I have tried to run as admin but still no go.
> > > Any advise?
> > > Cheers
> > > Bengt
> > >
> >
>

Hi Carl,
Then it is best I put both Copyright and Tm on that one :)
Cheers
Bengt

--- In DynoMotion@yahoogroups.com, "carlcnc" <cebcnc@...> wrote:
>
> Ha!
> good one Bengt
> 'Kflopers'
> it's a fun sounding name
> "Mach-er" always sounded so harsh
>
> Carl
>
>